___________________________________________________________________________

---------------------------------- MAX!  ----------------------------------
___________________________________________________________________________

#######################################
########## General Settings  ##########
#######################################

[General]

moduleEnabled = true

## The MAX! address of Homegear. It is recommended to change this to a random 3 byte hexadecimal
## value starting with 0xFD (e. g. 0xFD43AB). Only change this, when no MAX! devices
## are paired to Homegear as existing pairings will not work anymore!
#centralAddress = 0xFD0001

#######################################
################# CUL #################
#######################################

## The device family this interface is for
#[CUL]

## Specify an unique id here to identify this device in Homegear
#id = My-MAX-CUL

## When default is set to "true" Homegear will assign this device
## to new peers.
#default = true

## Options: cul, coc, cc1100
#deviceType = cul

#device = /dev/ttyACM0

## Should be "40" for MAX!
#responseDelay = 40

#######################################
########## TI CC1101 Module  ##########
#######################################

## The device family this interface is for
#[TI CC1101 Module]

## Specify an unique id here to identify this device in Homegear
#id = My-MAX-CC1101

## When default is set to "true" Homegear will assign this device
## to new peers.
#default = true

## Options: cul, coc, cc1100
#deviceType = cc1100

#device = /dev/spidev0.0

## Default: responseDelay = 95
## Should be "40" for CUL or COC and "45" for TI CC1101.
#responseDelay = 45

## The interrupt pin to use. "0" for GDO0 or "2" for GDO2.
## You only need to connect one of them. Specify the GPIO
## you connected the interrupt pin to below.
#interruptPin = 2

## The GPIO GDO0 or GDO2 is connected to. Specify which GDO to use above.
#gpio1 = 23

### Additional TI CC1190 Config ###

## The GPIO high gain mode of the CC1190 is connected to.
## Default: -1 (disabled)
#gpio2 = 5

## The hexadecimal value for the PATABLE of the TI CC1101.
## Default:
## - Without high gain mode: 0xC2
## - With high gain mode: 0x27 (maximum legally allowed setting)
#txPowerSetting = 0x27


#######################################
################ CUNX  ################
#######################################

## The device family this interface is for
#[CUNX]

## Specify an unique id here to identify this device in Homegear
#id = My-CUNX

## When default is set to "true" Homegear will assign this device
## to new peers.
#default = true

## Options: cul, cc1100, coc, cunx, hmcfglan, hmlgw
#deviceType = cunx

## IP address of your CUNX
#host = 192.168.178.100

## Port number your CUNX listens on. Normally 2323.
#port = 2323

## Default: responseDelay = 95
## Should be "40" for CUNX
#responseDelay = 40


#######################################
######### COC, SCC, CSM, CCD  #########
#######################################

## The device family this interface is for
#[COC, SCC, CSM, CCD]

## Specify an unique id here to identify this device in Homegear
#id = My-COC

## When default is set to "true" Homegear will assign this device
## to new peers.
#default = true

#deviceType = coc

#device = /dev/ttyAMA0

## Default: gpio1 = 0
## "17" for COC, SCC and CCD. Empty for CSM.
#gpio1 = 17

## Default: gpio2 = 0
## "18" for COC and SCC. "22" for CCD. Empty for CSM.
#gpio2 = 18

## Should be "40" for MAX!
#responseDelay = 40

## Default: stackPosition = 0 (= no stacking)
## Set stackPosition if you use the SCC and stacked multiple devices.
## Set stackPosition to "1" for the lowest device, to "2" for the device
## above that and so on.
# stackPosition = 0